We have all of our items in stock to make sure your order ships the same day if ordered by 2pm CST (Mon-Fri).
We have tons of iPod, Aux, and other installation accessories in our store, Click Here to see our store.
If you are not sure what year your car is CLICK HERE to be able to tell what year your car is by looking at the VIN number. This number is your cars "Vehicle Identification Number" and every car has one. Sometimes it is on the very front of the dash (near the windshield) and other times it can be found on the drivers side door.
- Installation
- How to use input
- Operation w/ iPhone
- Radio Removal
- FAQ/Contact Us
Installation
Overview: Installing this interface will require you to remove your factory radio in order to plug in the vehicle specific harness (Included). Installation time should be about 30min - 1.5hrs. Even for a novice. If you install exactly as instructed below, you will not need your radio security code.
Step 1: Turn off your car. Take out the key. Ignition key MUST be OFF and key OUT.
Step 2: Remove the radio from the dash. Do not unplug anything yet.
BONUS: We are including the radio removal keys (4 pcs) with this order! CLICK HERE for radio removal instructions using the supplied keys.Step 3: After you have removed your factory radio you will need to identify the approprite connector (20-pin pictured below) on the back of your radio. There will probably be a plug in this connector already installed. You will need to temporarily disconnect this plug (if equipped). Do not disconnect any other plugs.
Step 4: Connect the 20-pin connector on the included harness into the 20-pin connector on the back of your stereo. Then connect the 20-pin you disconnected in step #3 to the mating connecting on the other side of this harness. It becomes a pass-thru connection.
Ground the loose black wire (ring terminal): Then you will need to attach the ground wire to a screw on your radio. This is very easy, just either put it under the big rubber boot on the back of your stereo or tighten the ring terminal under a screw on your radio (to do this you would need to loosen a screw then tighten the ring terminal under it. This interface will not work at all if this is not grounded right. If you turn on your radio and it doesnt work, check the ground, and try a new grounding spot.
Step 5: You will now connect your iPOD cable to the Blitzsafe interface. You can do this by simply plugging in the 8-pin din connector on the iPOD cable to the empty 8-pin connector on the Blitzsafe interface.
Step 6: Test the interface, simply turn on your radio and press the CD or Disc button at most 2 times. At this point, you will hear the music from your iPOD thru your factory speakers. Your radio will display Disc 1 Track 99 on its display and your iPOD will start charging.
Step 7: Finish the installation by locating the interface in your vehicle (its only 3" x 1.25" x 1.25" in size) and should be easy to fit right behind the radio. You can just put it back behind your radio or extend the cable out to behind your glove box or center console. It will be very easy to find a mounting spot for this, as it will fit in any tight spot. As for routing the iPod cable (6 feet long), it is up to you to put it in the best place you need to use to your iPod. Please dont control your iPod or mp3 player while driving. If you need longer than 6 feet for your installation CLICK HERE for our Blitzsafe extension cable. Try letting the passanger be dj. Re-install the radio to the dash after a successful test.
IF THESE DO NOT WORK FOR YOU, OR YOU NEED MORE INFO, PLEASE E-MAIL US AT SALES@INTEGRATIONSOLUTIONS.NET OR CALL US AT 214-306-8031
- Installation
- How to use input
- Operation w/ iPhone
- Radio Removal
- FAQ/Contact Us
How to use input
Q: How do I select iPod Input as a source on my factory Radio?
Q: Can I still use the Buttons/Click Wheel on my iPOD/iPhone with this interface?
- You can access your iPOD by Pressing the CD or Disc button at most two times (depending if you have cd's in the am/fm cd player or not) This will allow you to go into iPOD mode. At this point your radio will say something like "Disc 1 Track 99" on the radio display. This display confirms that the iPOD mode has been completely synchronized and activated. If you dont have a CD player, you will press the CD button one time to enter into iPod mode. Without this interface installed, your radio will not do anything when you press the CD button two times. However, after you install this interface it will recognize the iPOD input.
Q: Can I control the ipod from the radio buttons?
- This interface allows you to keep full control of the iPod from the click wheel at all times. You can browse files and change playlist on the iPod. You can perform all functions of your iPOD like you normally would.
Q: Does this unit pause my iPod/iPhone player when I turn off my car?
- No, this unit will not display text either. All text and controls are from the controls on your iPod/iPhone itself.
- Yes, it does. It will auto pause (and then it will go to sleep a little bit later) your apple iPod when you turn off your car, that way you still have battery life when you get back to drive.
- Installation
- How to use input
- Operation w/ iPhone
- Radio Removal
- FAQ/Contact Us
Operation w/ iPhone
Q: How does this interface work with the iPhone?
Q: Will I be able to take a phone call thru the factory stereo when my iPhone is plugged in?
- When you connect your iPhone it will say "This accessory is not made for the iPhone". You will simply press no when it asks you if you want to go into airplane mode and then everything will work fine.
Q: Will this charge my iPhone too?
- If you have bluetooth then you can still use the bluetooth to take the phone call thru your stereo. If you dont have bluetooth you will have to literally pick up your iPhone and hold it to your ear to take a phone call.
- Yes, the new cable included with this interface will charge any iPhone (even the new 3G iPhone). Our cable has been updated to 5v technology. You dont need any new adapters for this.
- Installation
- How to use input
- Operation w/ iPhone
- Radio Removal
- FAQ/Contact Us
Radio Removal
BONUS: We are including the radio removal keys (4 pcs) with this order! CLICK HERE for radio removal instructions using the supplied keys.
- Installation
- How to use input
- Operation w/ iPhone
- Radio Removal
- FAQ/Contact Us
FAQ/Contact Us
Q: What does Level #2 (L2) mean?
Q: Is this compatible with my iPod/iPhone? What iPOD's is this compatible with?
- CLICK HERE to learn more about our Level iPod/iPhone rating assignments.
- Connects & charges iPod/iPhone (compatible Apple iPod/iPhone models listed below)
Q: Will my iPhone still say "This accessory is not made for the iPhone" everytime I connect?
- Yes, if you connect to the bottom dock connector (to charge) you will still see this message. You will simply press no when it asks you if you want to go into airplane mode and then everything will work fine.
- This interface only Charges Select Apple iPod's (Compatible models listed below) when connected via the bottom dock connector (It will also pause your iPod when you get out of the car, then it will turn off automatically). CLICK HERE to see a chart to be able to tell which iPod you have. This interface DOES NOT Require any additional charging adapter (Such as the Scoshe IFWB, Cablejive, or any other) with this interface. The cable that is included is setup to allow charging to even the newest ipods.
- iPod Classic - 3G, 4G, 5G, 6G, and 7G (120GB)
- iPod Nano - 1G, 2G, 3G, and Newest Nano 4G
- iPod Touch - 1G, Newest Touch 2G
- iPhone - 1G, and even iPhone 2G (also known as the 3G/3GS Network)
- Great question. Some people that buy from us, follow the installation instructions and use good judgment to make a great installation. If you do not want to do the installation yourself and are looking for a good place to install CLICK HERE to see our list of known installers. On another note, we are always adding installation places to our list of known installers. If you have it installed professionally please give us their contact info, and we will add them to our list. Often times, installers may not have much experience installing interfaces like these. If you are having this installed professionally, please give them our contact info before having them install it. This way we can answer any questions they might have while or before installation.
- Yes we do, we ship worldwide to every country. Whatever country you are in, we can ship there. Just click on the shipping tab to see our shipping options.
Call us @ 214-306-8031 if you have any questions when purchasing/installing this product. We do our own tech support to make sure our customers get friendly customer service.
